 The ring pictured is Welded Sterling Silver x 4ga Thick  Customer Demo of the Rings  Customer Demo of Multi-Rings |
"Round Wire Rings" A standard type of shaft-ring / cock-ring used to pleasure you and your mate.
Shaft-rings are Solid Sterling and are a big 4ga thick. Welded into a solid circle; these things are intense. Just think what a rush it will be to have solid circle of silver or *gold wrapped around your member.
Cock-rings are custom sized
to your anatomy (you provide the needed dimensions). The Shaft-ring pictured here can be made any diameter you need. I have priced out some common sizes below. Price will be based on the size of the ring. *Gold prices need custom quotes |
Price per Shaft Ring 1" ID (ID = inside Diam)= |
$55 (s&h) |
Price per Shaft Ring 1.5" ID (ID = inside Diam)= |
$55 (s&h) |
Price per Shaft Ring 2" ID (ID = inside Diam)= |
$60 (s&h) |
 Welded Sterling Silver 12mm Low Dome.  Welded 14k Gold 6mm Low Dome. |
"Low Dome Rings" Another standard type of shaft ring. The advantage of the Low dome wire is that since it is wider, it tends to spread out the pressure from the engorging member. This gives increased comfort for some individuals. But just like all things, there is a down side. Since the sides of the ring are much thinner than a round wire ring, there can be a little discomfort as the ring is tilted and the edge of the ring presses into the flesh. Few people seem to have a problem with this, but once in a while someone does. You should take this factor into consideration when buying a Low Dome Ring.
Low Dome Rings are Solid. Welded into a solid circle; these things are intense. Just think what a rush it will be to have solid circle of silver or *gold wrapped around your member.
These pieces are custom sized
to your anatomy (you provide the needed dimensions). The Shaft Ring pictured here can be made any diameter you need and comes in widths of 6mm, 8mm, and 12mm. I have priced out some common sizes below. Price will be based on the size of the ring. *Gold prices need custom quotes |
Price per Shaft Ring 1" ID (ID = inside Diam)= |
$55 (s&h) |
Price per Shaft Ring 1.5" ID (ID = inside Diam)= |
$55 (s&h) |
Price per Shaft Ring 2" ID (ID = inside Diam)= |
$60 (s&h) |
 "The ring pictured above is Sterling Silver, 2" Inside Diameter x 6mm wide with a Loop"  "The ring pictured above is 14ky Gold, 1 3/4" Inside Diameter x 8mm wide" |
"Screw-Down Rings First introduced on 11/26/99, these rings were intended to be a variation on my Screw-Down Collars.
These Shaft-rings are Solid Sterling (Solid Gold and Platinum are available as a custom order) and either come in a Low-Dome style or a Flat-Wire Style. Both styles can come with or without loops, and are available in various widths.
This Style of Shaft-Ring is held together with one Stainless Steel Button Head Cap Screw. The screw is attached and removed with an Allen wrench (provided).
Each piece is custom sized to your anatomy (you provide the needed dimensions). The Shaft Rings can be made with quite a few options.
Price per Shaft Ring will vary depending on the options you select
|
 "The ring pictured above is 10mm Flat Wire w/ Custom Bead-loop and a Heavy Ring |
"Flat Wire Rings" Similar to the Low-Dome Rings, except made from Flat Wire stock. They are available in both Silver and Gold, and can be made with many of the options found on the other styles of Sharft Rings.
As with all my cock rings, each piece is custom sized to your anatomy ..... (you are responsible for providing the correct dimensions).
Price per Shaft Ring will vary depending on the options you select
|
  |
"Custom Chastity Rings" Thanks to one of my customers who wanted one, I now have these nice pictures of another option available to you. Introduced on 2/26/2004, yet another quaint little device.
Unlike my other devices, this is not intended to give you pleasure, but take it away (grin).
The Chastity Ring pictured to the left is a Sterling Silver ring with (6)-4mm 14k Gold Balls going around the outside. This ring was designed to be held in place by a Frenum piercing and sit just behind the head of the penis; to make penetration either uncomfortable, or impossible.
*This device could also be designed as a complete circle, without the need of the piercing.
Like most of my designs; these pieces are custom sized
to your anatomy (you provide the needed dimensions). What the customer paid = $350 +(s&h) |
  |
"Custom Ball Stretcher" Thanks to one of my customers who wanted one, I now have these nice pictures of another option available to you. Introduced on 9/26/2006.
What's it for? Well, its for elongating your testicular sac of course. (ie: your balls baby).
Now, why on earth would someone want to stretch their balls? Hummm, good question. Because it is every mans dream? Beats me, but hey I am not the one to question my customers needs.
The pictured device is made from 4ga Sterling Silver round wire and was made to provide 1" of stretch.
Like most of my designs; these pieces are custom sized
to your anatomy (you provide the needed dimensions). What the customer paid = $175 +(s&h) |
Taking Measurements:I suggest that my clients use either a dress-makers tape measure or even a piece of string. Simply measure the circumference around the shaft and send me the measurement. Customer Question: Can you tell us how to measure for the classic shaft ring, specifically how do we measure for the proper size based on a persons specific anatomy, ie erect vs relaxed measurements etc. Well, there are really 2 ways.
These are my common suggestions. In the end the fit of the ring is up to you or the wearer. *Note: Measurement may be in Metric or Inch Standards. |